Power On:Remove earbuds from the charging case and the earbuds will turn on automatically, indicated by a red/blue flashing light.

Power off: Replace the earbuds back to the charging case, and close the cover of the case.

Note: If the earbuds do not turn on or off automatically, press and hold the earbud touch control until you hear the voice prompt “Power On” or “Power Off”.

To play audio from a Bluetooth device, you need to pair the device with your earbuds.

Power on your earbuds.

Wait up to 3 seconds for your earbuds to automatically pair, indicated by the voice prompt “Earbud Connected” and  blue LED on both earbuds.

Turn on Bluetooth mode on your device.

Select “Santana Tango” to initiate pairing, and the earbuds will automatically connect with your Bluetooth device, indicated by the voice prompt “Connected”. The LED lights on both earbuds will shut off. Some devices ask you to input the PIN “0000” as the password.

If earbuds fail to connect with each other, please turn off both earbuds. Turn on both earbuds again and double press the right-side touch control. The voice prompt “Earbud Connected” will indicate that the earbuds are successfully paired to each other. The LED will slowly blink blue on both earbuds. 

Touch the right earbud for 2-3 seconds to skip.

Touch the left earbud for 2-3 seconds to replay.

Answering a Call
When a call is incoming, you will hear a ring tone. Double press the L/R touch control to accept the call, or answer the call via your mobile phone.

Rejecting a Call
Long press the L/R touch control to reject an incoming call.

Ending a Call
Double press the L/R touch control to end the call, or hang up via your mobile phone.

2 full hours of charging time allow Tango Earbuds to have 3.5 hours of playtime. Fully charging the case will allow your earbuds to have 14 hours of playtime.

Charging Your Earbuds
To charge your earbuds, simply slide each earbud into its corresponding dock until the earbud is fully seated. The earbuds will begin charging, indicated by a solid red LED glow on the earbud and solid blue LED glow on the charging case. When the earbuds are fully charged, the LED on the earbuds will turn blue.

Charging Your Charging Case
To charge your charging case, plug the included micro-USB charging cable into the slot on the bottom of the charging case. Plug the other end into a USB adapter. The case will automatically begin charging, indicated by a   red LED Battery Indicator. When it is fully charged, the LED will be solid red.

Note: The voice prompt “Low Battery” will notify you when the earbuds need to be recharged.

Charging Your Earbuds
To charge your earbuds, simply slide each earbud into its corresponding dock until the earbud is fully seated. The earbuds will begin charging, indicated by a solid red LED glow on the earbud and solid blue LED glow on the charging case. When the earbuds are fully charged, the LED on the earbuds will turn blue.

Charging Your Charging Case
To charge your charging case, plug the included micro-USB charging cable into the slot on the bottom of the charging case. Plug the other end into a USB adapter. The case will automatically begin charging, indicated by a   red LED Battery Indicator. When it is fully charged, the LED will be solid red.

Note: The voice prompt “Low Battery” will notify you when the earbuds need to be recharged.

Charging Your Earbuds
To charge your earbuds, simply slide each earbud into its corresponding dock until the earbud is fully seated. The earbuds will begin charging, indicated by a solid red LED glow on the earbud and solid blue LED glow on the charging case. When the earbuds are fully charged, the LED on the earbuds will turn blue.

Charging Your Charging Case
To charge your charging case, plug the included micro-USB charging cable into the slot on the bottom of the charging case. Plug the other end into a USB adapter. The case will automatically begin charging, indicated by a   red LED Battery Indicator. When it is fully charged, the LED will be solid red.

Note: The voice prompt “Low Battery” will notify you when the earbuds need to be recharged.

If earbuds fail to connect with each other, please turn off both earbuds. Turn on both earbuds again and double press the right-side touch control. The voice prompt “Earbud Connected” will indicate that the earbuds are successfully paired to each other. The LED will slowly blue on both earbuds.

Power on: Press the Power ON/OFF button for 1 second until the white Power LED illuminates.

Power off: Press the Power ON/OFF button until the white Power LED turns off.

Power on the speaker. The blue Pairing LED blinks, indicating the speaker is ready to connect with your Bluetooth device.Turn on Bluetooth mode on your device.

Select “Santana Samba” to initiate pairing, and the speaker will automatically connect with your Bluetooth device, indicated by the steady blue Pairing LED. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 3 minute maximum to pair the speaker with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Turn off your Samba speaker

Turn off the Bluetooth mode on your device. 

Follow steps to connect the Samba Speaker to your device. 

If this doesn’t work, follow steps to reset Bluetooth settings on your Samba speaker below.

Hold Mode button for 5 Seconds.

Long press the (+) to skip tracks.

Long press the (-) to repeat tracks.

Short press (+) to increase the volume.

Short press (-) to decrease the volume.

Answering a Call: When a call is incoming, you will hear a ringtone. Press the MFB (Multi-Function Button) button once to accept the call, or answer the call via your mobile phone.

Rejecting a Call: Hold the MFB button to reject the incoming call. 

Ending a Call: Press the MFB button once to end the call, or hang up via your mobile phone.

If you’ve purchased 2 Samba speakers, you can play music from a stereo pair. Follow these instructions to take advantage of this feature:

Disconnect Samba from all Bluetooth devices.

Power on both speakers.

Hold the MODE button for 2 seconds on one speaker, and release when the voice prompt says “Speaker Searching”

The speakers will connect to each other indicated by the voice prompt “Speakers Connected”. The Pairing LED on one speaker will flash blue; it will be steady blue on the other speaker.

Turn on the Bluetooth device, and select Santana Samba.

Once connected, both Pairing LEDs will be steady blue.

No, you can only pair two Samba speakers together at this time.

Yes, however, your TV must have Bluetooth Capabilities.

Go to the settings menu on your TV.

Select Sound.

Turn on Bluetooth.

Pair to “Samba.”

Once connected to your device, you can view the battery life from your device’s screen. You will also hear the voice prompt “Low Battery” when your device needs to be recharged.

Once connected to your device, you can view the battery life from your device’s screen. You will also hear the voice prompt “Low Battery” when your device needs to be recharged.

Before charging, make sure the speaker has been switched off.

Plug the USB cable into the charging port of the speaker; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the red light remains illuminated on the speaker.

A full charge takes approximately 2 hours, and then the red light will turn blue when fully charged.

Power on: Press and hold the Power ON/OFF button until you hear the voice prompt “Power On”.

Power off: Press and hold the Power ON/OFF button until you hear the voice prompt “Power Off”.

To play audio from a Bluetooth device, you need to pair the device with your speaker.

Power on the speaker. The LED indicator flashes blue accompanied by the voice prompt “Bluetooth Mode”, then “Pairing” indicating the speaker is ready to connect with your Bluetooth device.

Turn on Bluetooth mode on your device.

Select “Santana Europa” to initiate pairing, and the speaker will automatically connect with your Bluetooth device, indicated by a steady blue LED. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 3 minute maximum to pair the speaker with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Make sure the Europa is not connected to another device.

Hold down the power button (3-4 seconds) to reset Bluetooth to forget all previous connections.

Turn off Bluetooth.

Power on Europa.

Pair.

Hold the Power button for 3 seconds.

Long press the Vol(+) to select next track. 

Long press the Vol(-) to select previous track.

Short press the Vol(+) or Vol(-) to adjust volume. You will hear a “Beep” when you’ve reached the max volume.

Short Press “Phone” button once to answer.

Short Press “Phone” button once during a call to hang up.

Hold “Phone” button to reject call.

Yes, our Europa Speaker comes with a Micro-USB Charging Cable.

Before charging, make sure the speaker has been switched off.

Plug the USB cable into the charging port of speaker; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the battery indicator will flash.

A full charge takes approximately 4 hours, and then the battery indicators will remain solid when fully charged.

Warning: You must use the original cable to charge the Bluetooth speaker, otherwise it may damage the speaker. Proper charger voltage must be 5V with a current rated at 115mA.

Optional 18V Fast Charger: The Europa speaker is equipped with an 18V fast charging port. Should you choose to take advantage of the fast charge feature, you'll need to purchase a separate 18V wall charger. The proper charger specifications are listed below, and a link to a similar charger is included here: https://www.amazon.com/KFD-Universal-Compatible-5-5x2-1mm-6-5x4-4mm/dp/B07R33J1BM/ref=sr_1_1_sspa?keywords=18V+2A&qid=1568122178&s=electronics&sr=1-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyMkxKTU9VQloyMjJRJmVuY3J5cHRlZElkPUExMDM2NTUyM1AzUTNaREJUTzFDVCZlbmNyeXB0ZWRBZElkPUEwMTkzNTUxMTI4VUtTWERTN1ZWTCZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

Output Voltage: 18V

Output Current: 2A

Plug Size: 4.0mm x 1.7mm

Before charging, make sure the speaker has been switched off.

Plug the USB cable into the charging port of speaker; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the battery indicator will flash.

A full charge takes approximately 4 hours, and then the battery indicators will remain solid when fully charged.

Warning: You must use the original cable to charge the Bluetooth speaker, otherwise it may damage the speaker. Proper charger voltage must be 5V with a current rated at 115mA.

Optional 18V Fast Charger: The Europa speaker is equipped with an 18V fast charging port. Should you choose to take advantage of the fast charge feature, you'll need to purchase a separate 18V wall charger. The proper charger specifications are listed below, and a link to a similar charger is included here: https://www.amazon.com/KFD-Universal-Compatible-5-5x2-1mm-6-5x4-4mm/dp/B07R33J1BM/ref=sr_1_1_sspa?keywords=18V+2A&qid=1568122178&s=electronics&sr=1-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyMkxKTU9VQloyMjJRJmVuY3J5cHRlZElkPUExMDM2NTUyM1AzUTNaREJUTzFDVCZlbmNyeXB0ZWRBZElkPUEwMTkzNTUxMTI4VUtTWERTN1ZWTCZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

Output Voltage: 18V

Output Current: 2A

Plug Size: 4.0mm x 1.7mm

It takes 4 Hours to charge the Europa Speaker.

The playtime on the Europa Speaker is 10 Hours (depending on the volume).

Yes, however, your TV must have Bluetooth Capabilities.

Go to the settings menu on your TV

Select Sound

Turn on Bluetooth

Pair to “Europa”

Power on: Hold the MULTIFUNCTION (MF) button for 3 seconds until the white light illuminates.

Power off: Hold the MF button for 4 seconds until the red light illuminates then turns off.

To play audio from a Bluetooth device, you need to pair the device with your earbuds.

1. Hold the MF button for 3 seconds to power on the earbuds, indicated by the voice prompt “Power on”, then “Pairing”. The light blinks white, indicating the earbuds are ready to connect with your Bluetooth device.

2. Turn on Bluetooth mode on your device.

3. Select “Santana Suenos” to initiate pairing, and the earbuds will automatically connect with your Bluetooth device, indicated by a white light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Turn off your earbuds.

Turn on your earbuds, but don’t release the power button until you hear the voice prompt, “Pairing”.

Long press the Vol(+) to select next track.

Long press the Vol(-) to select previous track.

Short press (+) to increase the volume.

Short press (-) to decrease the volume.

To answer a call: When a call is incoming, you will hear a ring tone. Press the MF button once to accept the call, or answer the call via your mobile phone.

Reject: Double press the MF button to reject the incoming call.

To end a call: Press the MF button once to end the call, or hang up via your mobile phone.

Before charging, make sure the earbuds have been switched off.

Plug the USB cable into the charging port of earbuds; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the red light remains illuminated on the earbuds.

A full charge takes approximately 2 hours, and then the red light will turn white when fully charged.

Warning: You must use the original cable to charge the Bluetooth earbuds, otherwise it may damage the earbuds. Proper charger voltage must be 5V with a current rated at 115mA.

These earbuds use a non-detachable built-in rechargeable battery. In order to prevent damage to the earbuds, please do not remove the battery.

The voice prompt “Battery Low” will notify you when the earbuds need to be recharged.

Our Suenos Earbuds come with 3 different sizes of Silicone Ear Tips. Try each size until you find the one that fits best.

Hold 3 seconds the Power/Play/Phone button to power on the earbuds.

To play audio from a Bluetooth device, you need to pair the device with the Headset. You can pair up to eight devices.

On your Bluetooth device, switch on Bluetooth and scan for devices in its Bluetooth menu. Hold 3 seconds the Power/Play/Phone button to power on the headset.

You will hear the voice “Power on,” “Pairing.” Meanwhile, the function LED will turn flash blue/red.

When “CANTO” appears on the device list of your Bluetooth device, select it to initiate pairing. The function LED turn slow flash blue after pairing is established.

Turn off your earbuds

Turn on your earbuds, but don’t release the power button until you hear the voice prompt, “Pairing.”

Long press (+) to skip a song

Long press (-) to repeat a song

Short press (+) to increase the volume

Short press (-) to decrease the volume

To answer a call: When a call is coming, the ring tone will be heard by headset, press "Power/Play/Phone" button once to accept the call or answer the call via your mobile phone.

Reject: Long press the "Power/Play/Phone" button to reject the incoming call.

To end a call: While speaking, press "Power/Play/Phone" button once to end the call or hang up on your mobile phone.

Cancel Dialing: Press the "Power/Play/Phone" button once when dialing to cancel the dialing.

Last Call Redialing: In stand-by mode, double press the "Power/Play/Phone" button to redial the last call.

Approximately 1.5 hours

When the function LED light flashes red color or if the headset powers off automatically, it's time to recharge the battery.

Our Cantos Earbuds come with 3 different sizes of Silicone Ear Tips. Try each size until you find the one that fits best. 

Power on: Hold the MULTIFUNCTION (MF) button for 3 seconds until the LED flashes blue.

Power off: Hold the MF button for 4 seconds until the LED turns red then turns off.

To play audio from a Bluetooth device, you need to pair the device with your earbuds.

With the earbuds turned off, hold the MF button for 6-8 seconds to enter pairing mode, indicated by the voice prompt “Pairing”. The LED flashes blue and red, indicating the earbuds are ready to connect with your Bluetooth device.
Turn on Bluetooth mode on your device.

Select “Santana Fuego” to initiate pairing, and the earbuds will automatically connect with your Bluetooth device, indicated by a blue light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 5 minute maximum to pair the earbuds with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Turn off your earbuds

Turn on your earbuds, but don’t release the power button until you hear the voice prompt, “Pairing”.

Long press the Vol(+) to select next track. 

Long press the Vol(-) to select previous track.

Short press (+) to increase the volume

Short press (-) to decrease the volume

Long press the ANC button to turn on/off the Active Noise Cancellation function, indicated by a blue light and voice prompt.

To answer a call: When a call is incoming, you will hear a ring tone. Press the MF (Multi Function) button once to accept the call, or answer the call via your mobile phone.

Reject: Hold the MF button for 1-2 seconds to reject the incoming call.

To end a call: Press the MF button once to end the call, or hang up via your mobile phone.

In order to charge Fuego Headphones, you must use a Micro USB Charging Cable.

Before charging, make sure the earbuds have been switched off.

Plug the USB cable into the charging port of earbuds; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the red light remains illuminated on the earbuds.

A full charge takes approximately 2 hours, and then the red light will turn blue when fully charged.

Warning: You must use the original cable to charge the Bluetooth earbuds, otherwise it may damage the earbuds. Proper charger voltage must be 5V with a current rated at 102mA.

These earbuds use a non-detachable built-in rechargeable battery. In order to prevent damage to the earbuds, please do not remove the battery.

Note: The voice prompt “Low Battery” will notify you when the earbuds need to be recharged.

Yes, the earbuds are rated IP64. IP64 rated water resistance protects against splashing water, dust and sand.

Power on: Hold the MULTIFUNCTION (MF) button for 3 seconds until the blue light illuminates.

Power off: Hold the MF button for 4 seconds until the red light illuminates then turns off.

To play audio from a Bluetooth device, you need to pair the device with your earbuds.

Hold the MF button for 3 seconds to power on the earbuds, indicated by the voice prompts “Power on”, then “Pairing”. The light blinks red and blue, indicating the earbuds are ready to connect with your Bluetooth device.

      2. Turn on Bluetooth mode on your device.

Select “Santana Gypsy” to initiate pairing, and the earbuds will automatically connect with your Bluetooth device, indicated by a blue light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 5-minute maximum to pair the earbuds with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Turn off your earbuds

Turn on your earbuds, but don’t release the power button until you hear the voice prompt, “Pairing”.

Long press the Vol(+) to select next track. 

Long press the Vol(-) to select previous track. 

Short press (+) to increase the volume.

Short press (-) to decrease the volume.

To answer a call: When a call is incoming, you will hear a ringtone. Press the MF button once to accept the call, or answer the call via your mobile phone.

Reject: Double press the MF button to reject the incoming call.

To end a call: Press the MF button once to end the call, or hang up via your mobile phone.

In order to charge Gypsy Headphones, you must use a Micro USB Charging Cable.

A full charge takes approximately 2 hours, and then the red light will turn blue when fully charged.

Our Gypsy Earbuds come with 3 different sizes of Silicone Ear Tips. Try each size until you find the one that fits best.

Power on: Hold the MULTIFUNCTION (MF) button for 3 seconds until the blue light illuminates.

Power off: Hold the MF button for 4 seconds until the red light illuminates then turns off.

To play audio from a Bluetooth device, you need to pair the device with your earbuds.

On your Bluetooth device, switch on Bluetooth and scan for devices in its Bluetooth menu. 
Hold 3 seconds the Power/Play/Phone button to power on the headset. You will hear the voice “Power on”, “Pairing”. Meanwhile, the function LED will turn flash blue/red.

When “ RUMBA ” appears on the device list of your Bluetooth device, select it to initiate pairing. The function LED turn slow flash blue after pairing is established.

Note: If pairing fails, switch the headset off and then back on so that the function LED flashes blue color again.

lf pairing fails, switch the headset off and then back on so that the function LED flashes blue color again.

Long press the Vol(+) to select next track. 

Long press the Vol(-) to select previous track.

Short press Vol(+) to increase the volume.

Short press Vol(-) to decrease the volume.

When a call is coming, the ring tone will be heard by headset, press "Power/Play/Phone" button once to accept the call or answer the call via your mobile phone.

In order to charge the Rumba Earbuds, you must use a Micro USB Charging Cable.

Our Rumba Earbuds come with 3 different sizes of Silicone Ear Tips.

Power on: Hold the MFB Button.The LED indicator will flash red/blue.

Power off: Hold the MFB Button. The LED indicator will turn off.

To play audio from a Bluetooth device, you need to pair the device with your headphones.

Turn on the headphones. The light blinks red and blue, indicating the headphones are ready to connect with your Bluetooth device.

Turn on Bluetooth mode on your device.

Select “Santana Oye” to initiate pairing, and the headphones will automatically connect with your Bluetooth device, indicated by a blue light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 5 minute maximum to pair the headphones with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Turn off your headphones.

Turn on your headphones, but don’t release the power button until you hear the voice prompt, “Pairing”.

Long press the Volume(+) to select next track. 

Long press the Volume(-) to select previous track.

Short press (+) to increase the volume.

Short press (-) to decrease the volume.

Answering a Call
When a call is incoming, you will hear a ringtone. Press the MFB button once to accept the call, or answer the call via your mobile phone.

Rejecting a Call
Long press the MFB button to reject the incoming call.

Ending a Call
Press the MFB button once to end the call, or hang up via your mobile phone.

Before charging, make sure the headphones have been switched off.

Plug the USB cable into the charging port of headphones; plug the other side of the USB cable into a USB charger or other charging device. Charging will start, and the red light remains illuminated on the headphones.

A full charge takes approximately 2 hours, and then the red light will turn off when fully charged.

Warning: You must use the original cable to charge the Bluetooth headphones, otherwise it may damage the headphones. Proper charger voltage must be 5V with a current rated at 1A.

These headphones use a non-detachable built-in rechargeable battery. In order to prevent damage to the headphones, please do not remove the battery.

Note: The voice prompt “Battery Low” will notify you when the headphones need to be recharged.

A full charge takes approximately 2 hours, and then the red light will turn on when fully charged.

Press the ANC On/Off button to turn Active Noise Cancellation on/off. 

The LED indicator will turn green when the ANC is on.

The green LED indicator will turn off when ANC is off.

Power on: Slide the Power On/Off switch from Off to On. The LED indicator will flash red/blue.

Power off: Slide the Power On/Off switch from On to Off. The LED indicator will turn off.

Your headphones can simultaneously connect with up to two mobile devices. Follow these steps to take advantage of this feature:

Connect to Device 1:
To play audio from a Bluetooth device, you need to pair the device with your headphones.

Turn on the headphones. The light blinks red and blue, indicating the headphones are ready to connect with your Bluetooth device.

Turn on Bluetooth mode on your device.

Select “Santana Noche” to initiate pairing, and the headphones will automatically connect with your Bluetooth device, indicated by a blue light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Connect to Device 2:

Turn on the headphones. The light blinks red and blue, indicating the headphones are ready to connect with your Bluetooth device.

Turn on Bluetooth mode on your device.

Connect to “Santana Noche” to initiate pairing, and the headphones will automatically connect with your Bluetooth device, indicated by a blue light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Connect to Both Devices:

Turn on Bluetooth mode on device 1.

Connect to “Santana Noche” to initiate pairing, and the headphones will now be connected to both devices.

Note: You can only listen to music or answer calls from one device at a time. You must stop music or end a call from one device to use the other device.

Long press the Volume(+) to select next track. 

Long press the Volume(-) to select previous track.

Short press (+) to increase the volume.

Short press (-) to decrease the volume.

Answering a Call
When a call is incoming, you will hear a ring tone. Press the MFB (Multi Function Button) button once to accept the call, or answer the call via your mobile phone.

Rejecting a Call
Long press the MFB button for 1 second to reject the incoming call.

Ending a Call
Press the MFB button once to end the call, or hang up via your mobile phone.

In order to charge Noche Headphones, you must use a Micro USB Charging Cable.

A full charge takes approximately 2.5 hours, and then the red light will turn blue when fully charged.

Slide the ANC On/Off switch from Off to On to turn Active Noise Cancellation on. The LED indicator will turn green.

Slide the ANC On/Off switch from On to Off to turn Active Noise Cancellation off. The green LED indicator will turn off.

The Noche Headphones are not waterproof.

Power ON: Hold the Power On/Off button until the LED indicator flashes green/blue.

Power OFF: Hold the Power On/Off button for 5 seconds. Release the button, then the headphones will turn off.

To play audio from a Bluetooth device, you need to pair the device with your headphones.

Turn on the headphones. The light blinks green and blue, indicating the headphones are ready to connect with your Bluetooth device.

Turn on Bluetooth mode on your device.

Select “Santana Zebop” to initiate pairing, and the headphones will automatically connect with your Bluetooth device, indicated by a green light and voice prompt “Connected”. Some devices ask you to input the PIN “0000” as the password.

Note: Generally, there is a 5 minute maximum to pair the headphones with your Bluetooth device, otherwise retry steps 1 to 3 to pair again.

Long press the Volume(+) to select next track. 

Long press the Volume(-) to select previous track.

Short press Volume(+) to increase the volume.

Short press Volume(-) to decrease the volume.

Answering a Call
When a call is incoming, you will hear a ring tone. Press the MFB (Multi Function Button) button once to accept the call, or answer the call via your mobile phone.

Rejecting a Call
Long press the MFB button to reject the incoming call.

Ending a Call
Press the MFB button once to end the call, or hang up via your mobile phone.

A full charge takes approximately 2.5 hours, and then the red light will turn off when fully charged.